Sensibo logo mark

Setup & remote Sensibo troubleshooting

Air conditioner doesn't respond to Sensibo

The app sends a command but the split system ignores it or does something else. Usually the signal isn't reaching the unit, or the remote picked during setup isn't quite right.

Checked

  • Sky
  • Air
  • Air Pro

Start here

What are you seeing?

Pick the closest match and we'll point you to the fix most likely to sort it.

Why it happens

The Sensibo controls your air conditioner the same way its remote does, by sending infrared signals. It has no wired connection to the unit, so if the signal doesn't reach the air conditioner, nothing happens.

When the signal does arrive but the unit does the wrong thing, the remote picked during setup is the usual cause. Auto-detect finds your brand, but brands make many remotes with slightly different codes, and the first match isn't always the one your unit expects.

Quick checks first

Run these checks before moving on to the fixes.

Checklist 0 of 2 checked
Check the Sensibo has power

The light on the Sensibo glows once each time it sends a command. If it never glows, check the cable and power supply first.

Try the original remote

If the air conditioner ignores its own remote too, the problem is the unit, not the Sensibo.

Fixes, most likely first

Work down the list and stop when it's fixed.

  1. The signal isn't reaching the air conditioner

    How to tell. The Sensibo's light glows when you send a command, but the air conditioner doesn't react at all.
    • Face the glossy front at the unit

      The black glossy part of the Sensibo is where the signal comes from. Turn it so it faces the air conditioner, with nothing in the way.

    • Move it closer

      Sensibo suggests about 1 metre from the air conditioner. Try a few positions if the first one doesn't work.

    • Test it right next to the unit

      Hold the Sensibo very close to the air conditioner and send a command. A phone power bank lets you do this without a power point nearby. If it works up close, the fix is a better spot, not new settings.

  2. The remote picked during setup isn't quite right

    How to tell. The air conditioner responds to some commands, or responds the wrong way, even with the Sensibo close by.
    • Open the remote settings

      In the Sensibo app, open your device, tap the settings cog and tap Change remote type.

    • Try a similar remote variant

      If auto-detect found your brand, tap Manual setup, then tap Select under Recommended method and test one of the similar variants it offers. Each variant handles modes, fan speeds and swing slightly differently.

    • Run auto-detect again if you need to

      Tap Auto Detect, point the air conditioner's own remote at the front of the Sensibo and press its power button. If the app can't detect the remote, fit fresh batteries, move closer and tap Try again.

    • No remote? Pick it by hand

      Choose your air conditioner's brand from the list and test each remote configuration until one works. It takes longer than auto-detect, so use it only when auto-detect fails or the remote is lost.

    • Test every function

      Check on and off, temperature, each mode, fan speeds and swing before you settle on a variant.

  3. A window or portable unit is out of step with the app

    How to tell. Your air conditioner is a window or portable unit with buttons on it, and the trouble started after someone used those buttons.
    • Note what the app shows

      Open the Sensibo app and write down the mode, temperature, fan speed and any other setting it shows for the unit.

    • Match the unit to the app

      Using the buttons on the air conditioner, set every one of those settings to exactly what the app shows.

    • Use only the app from now on

      Control the unit from the Sensibo app and leave its buttons alone. If you do use them, match the unit to the app again afterwards.

    • Still wrong? Try another remote variant

      If the commands are still off while you only use the app, work through the remote fix above and try a different variant.

On your device

Sensibo Sky Smart AC Controller Sensibo Sky
  • Look for the blue light

    The Sky shows a blue light when it sends a signal. If you see it and the air conditioner still doesn't react, start with the first fix.

Sensibo Sky Smart AC Controller

Frequently asked questions

Yes. It sends infrared, like the remote, so it needs a clear line of sight to the unit.

Yes, on a split system. Sensibo sends a split system the full setting with every command, so the next command from the app puts the unit back to what the app shows.

Sensibo sends window and portable units step commands, like one degree warmer, instead of the full setting. Using the unit's own buttons puts it out of step, so match it to the app and control it from the app only.

Still need a hand?

We answer most messages within one business day. If your question is about an existing order, have your order number ready. It speeds things up.

Contact us